Tìm kiếm phụ kiện

AUT.LED.LDH.S

LED cover holder for the optical bench. The holder can be used to quickly exchange the LED cover to change the wavelength of the light source.

AUT.LED.PHDIODE.S

Calibrated photodiode holder for optical bench. This holder is used to measure the light intensity.Range: 350 - 1100 nm, 3.6 x 3.6 mm active area.An additional cover for a neutral density filter is supplied with the holder.

AUT.PS12V1A

12 V, 1 A DC power supply for the Autolab deuterium/halogen compact light source.

AUT.RCE

Autolab Rotating Cylinder Electrode (RCE) with a non-carbon liquid contact provides superior noise-free corrosion measurements. The RCE’s Hg contact produces smooth and accurate data that requires no special handling or tools for use in your lab.With the highest rotation rate among commercially available systems, the Autolab Rotating Cylinder Electrode allows you to simulate the widest variety of pipe flow conditions in your lab. The RCE has double the rotation rate of any other 12 mm rotating cylinder electrode making achievable flow rates are 50% higher than any other commercially available RCE.Maximum simulated turbulent flow rates: 1 inch/2.66 cm pipe with schedule 40 is 365 cm/s24 inch/57.48 cm pipe with schedule 40 is 566 cm/sThe Autolab RCE is very compact, only a tenth of the size of other commercially available RCEs. You can access the full rotation rate of the Autolab RCE (100-5000 rpms) with a 12 mm cylinder. Operating temperature range: max 40 C°Exposed sample surface: 3 cm2Image shows RCE and controller, RRDE cell, PGSTAT204 and NOVA software. Keywords: Rotating Cylinder Electrode, Corrosion, RCE, pipe flow, turbulent flow, corrosion in pipes, pipes, Reynolds number, cylindrical sample.

AUT.RDE.CTRL.S

Metrohm Autolab Motor controller unit used to control the rotation rate of the rotating disk, rotating cylinder and rotating ring-disk electrodes. It can be used manually or remotely from the NOVA ot INTELLO software

AUT.RDE.ELCBL

Electrode cable to connect the Metrohm Autolab potentiostats/galvanostats to the rotating disk and rotating cylinder electrodes.

AUT.RDE.M3

The Autolab RDE with an M3 thread is a high-end rotating disk electrode for measurements on systems where high rotation speed and low noise are required. The unit can go up to 10,000 rpm, a liquid Hg contact guarantees low noise. The PCTFE shaft has been designed to fit in Metrohm cell vessels, but also fits on most other electrochemical cells. The tip diameter is 8 mm with a glass shaft and an active surface diameter of 2 mm.The rotation speed of the RDE is controlled manually with the button on the front of the motor control unit. The RDE can also be controlled remotely with the Autolab software. The rotation speed can be varied continuously between 100 and 10,000 rpm with a resolution of 1 rpm.

AUT.RDE.ROT.M3.S

Autolab rotator for the rotating disk electrode with M3 thread

AUT.RDE.ROT.S

Autolab rotator for the rotating disk and rotating cylinder electrodes.

AUT.RDE.S

The Autolab RDE is a high-end rotating disk electrode for measurements on systems where high rotation speed and low noise are required. The unit can go up to 10,000 rpm, a liquid Hg contact guarantees low noise. The PCTFE shaft has been designed to fit in Metrohm cell vessels, but also fits on most other electrochemical cells. The tip diameter is 10 mm, with an active surface diameter of 3 mm or 5 mm.The rotation speed of the RDE is controlled manually with the button on the front of the motor control unit. The RDE can also be controlled remotely with the Autolab software. The rotation speed can be varied continuously between 100 and 10,000 rpm with a resolution of 1 rpm.

AUT.RHD.TSCBATT

The TSC Battery is a closed measuring cell intended for assembling half or full battery or supercap cells with e.g. active materials and separators. It is also suitable for investigating solid or gel-like samples in contact with metal electrodes in a plate/plate geometry.You have flexibility with cell configuration either two and three electrode measurements can be performed by inserting a microreference electrode from the side.The standard variant contains flat metal electrodes. For current collectors designed for using elemental lithium as electrode material please refer to the extended variant."This cell is airtight and thus shielded against atmosphere and can be used with moisture-sensitive samples.

AUT.RHD.TSCSURF

The TSC Surface is a closed cell designed for electrochemical measurements on flat samples and can be used to study the electrochemical interface between a well defined working electrode and solution and the kinetics of electron transfer reactions. This cell, like all other cells is suitable for measurements with ionic liquids, but it can also be used with aqueous and organic solvents and for corrosion measurements.

AUT.RRDE.S

The Autolab RRDE is a low-noise rotating ring disk electrode that can be used to perform electrochemical measurements under controlled hydrodynamic conditions. The ring and disk electrode assembly provides the means to detect reaction intermediates in situ through collection experiments.The Autolab RRDE uses 2 identical friction-less mercury contacts for low noise measurements and can be used with any Autolab potentiostat/galvanostat fitted with the BA, dual-mode bipotentiostat module.The rotation speed of the RRDE is controlled manually with the button on the front of the motor control unit. The RRDE can also be controlled remotely with the Autolab software. The rotation speed can be varied continuously between 100 and 10,000 rpm with a resolution of 1 rpm.

AUTSRV.BSTR10.CELL.S

100 mOhm dummy cell for testing the Booster10A.

AUTSRV.BSTR20.CELL.S

50 mOhm dummy cell for testing the Booster20A.

BA.MAC.204

The BA is a dual-mode bipotentiostat module that converts the Autolab into a double channel potentiostat with which measurements on 2 working electrodes can be performed sharing the same counter and reference electrode.In the Bipotentiostat mode, a fixed potential is applied to the second channel (second Working Electrode) while applying a potential step or a sweep to the first channel (first Working Electrode). In the Scanning Bipotentiostat mode, a potential offset with respect to the first channel is applied to the second channel.

BA.S

The BA is a dual-mode bipotentiostat module that converts the Autolab into a double channel potentiostat with which measurements on 2 working electrodes can be performed sharing the same counter and reference electrode.In the Bipotentiostat mode, a fixed potential is applied to the second channel (second Working Electrode) while applying a potential step or a sweep to the first channel (first Working Electrode). In the Scanning Bipotentiostat mode, a potential offset with respect to the first channel is applied to the second channel.

BST.EMER.BUTN

The Booster20A is fitted with an emergency stop button which can be position in close proximity to the instrument. This button can be used to immediatly disconnect the Booster20A from the cell if necessary.

BSTR10A.PG204.M204.S

The Booster 10A module increases the maximum current of the PGSTAT204 or M204 to 10 Ampere. The compliance voltage of the system is 20 V in combination with the Booster10A.With its fast response time, the Autolab Booster 10A has been optimized to perform electrochemical impedance measurements, in combination with the FRA32M module, on fuel cells, batteries and super-capacitors. The booster is able to handle active as well as passive cells. The Booster 10A can be used to measure the charge and discharge characteristics of super-capacitors, perform measurements on fuel cells or perform DC or AC measurements on large area electrodes.

BSTR10A.S

The Booster 10A module increases the maximum current of the PGSTAT100N, PGSTAT128N, PGSTAT302N, PGSTAT204 or M204 to 10 Ampere. The compliance voltage of the system is 20 V in combination with the Booster10A.With its fast response time, the Autolab Booster 10A has been optimized to perform electrochemical impedance measurements, in combination with the FRA32M module, on fuel cells, batteries and super-capacitors. The booster is able to handle active as well as passive cells. The Booster 10A can be used to measure the charge and discharge characteristics of super-capacitors, perform measurements on fuel cells or perform DC or AC measurements on large area electrodes.

BSTR20.EMG.S

The Booster20A is fitted with an emergency stop button which can be position in close proximity to the instrument.

BW840000463

BAC151x Probe Adaptor to connect B&W Tek Lab grade Raman probes to BAC151x Video microscope sampling system. Remove the standard shaft and distance regulator, to use the adaptor and connect the probe head to the video microscope. 3 adaptors per pack.

BWT-810000468

Cleaner for SMA905 and FC/PC connections.

BWT-810000469

FC/PC and FC/APC receptacle cleaner recommended for i-Raman Pro/Prime, STRam, QTRam. Do not use on SMA.FRC

BWT-810000623

BAC151x-TRI tripod adapter for the BAC151x sampling system with Raman video microscope.

BWT-810000719

Power cord for EU power for use with portable Raman systems.BWPC-EU

BWT-810000721

Carrying Case for i-Raman Pro and Prime series. Includes a soft, black carrying case with wheels and custom-cut foam for packing and safely carrying the i-Raman Pro, i-Raman Prime, STRam, or QTRam.CCRM

BWT-840000117

Raman flow-through cell made of stainless steel, for inline Raman measurements of liquid samples by interfacing with standard laboratory probe (9.5 mm diameter; probe is not included in scope of delivery).

BWT-840000130

Optional immersion shaft for BAC100/BAC102 Raman probes with an excitation wavelength of 532 nm or 785 nm. Equipped with a 76.2 mm long body made of 316L stainless steel with an outer diameter of 12.0 mm and a silica window that is sealed with an O-ring made of perfluoro rubber. Operating distance 5.0 mm in air. Can be used at -55 °C to 200 °C. The seal is liquid-tight at low pressure ( 1 bar).

BWT-840000131

Optional immersion shaft for BAC100/BAC102 Raman probes with an excitation wavelength of 532 nm or 785 nm. Equipped with a 76.2 mm long body made of 316L stainless steel with an outer diameter of 12.0 mm and a sapphire-glass window that is sealed with an O-ring made of perfluoro rubber. Operating distance 5.0 mm in air. Can be used at -55 °C to 200 °C. The seal is liquid-tight at low pressure ( 1 bar).

BWT-840000290

NanoRam (model BWS456-785 only) Rechargeable lithium-ion battery.

BWT-840000294

Lithium-ion battery charging cradle.(for charging NR-BAT and TID-BAT only).

BWT-840000295

Borosilicate glass vials (diameter 15 mm), package of 6, with pouch.

BWT-840000296

Stylus/pen combo for touch screens.NR-STY

BWT-840000298

NanoRam hard plastic rugged carrying case.

BWT-840000301

Power Adapter 12 V DC; 2.0 A.

BWT-840000307

NanoRam documentation set including Product Manual and NanoRam ID Installation Instructions.

BWT-840000322

Microscope objective, infinity-corrected, 10x, working distance (mm) = 16, focal length (mm) = 20, numerical aperture (NA) = 0.3.RML110A

BWT-840000323

Microscope objective, infinity-corrected, 20x, working distance (mm) = 12, focal length (mm) = 10, numerical aperture (NA) = 0.4.RML120A

BWT-840000325

Microscope objective, infinity-corrected, 50x, working distance (mm) = 9.15, focal length (mm) = 4, numerical aperture (NA) = 0.55.RML150A

BWT-840000328

Microscope objective, infinity-corrected, 100x, working distance (mm) = 3.2, numerical aperture (NA) = 0.8, Focal length (mm) = 2.RML1100A

BWT-840000329

Pouch for 15 mm vials.

BWT-840000332

Tablet holder compatible with all models of BAC100/BAC102 lab-grade fiber-optic Raman probe with 9.5 mm shaft diameter.

BWT-840000342

Right-angle adapter for hands-free measurement using handheld Raman instruments. Compatible with NanoRam-1064 and TacticID Mobile.

BWT-840000343

Point-and-shoot adapter for handheld Raman instruments. Compatible with NanoRam-1064 and TacticID Mobile.

BWT-840000344

Vial holder adapter, compatible with 15 mm-diameter vials.

BWT-840000345

Handheld Raman accessories: bottle adapterNR2-BSA

BWT-840000346

NanoRam tablet holder adapter.

BWT-840000347

Immersion probe – 30.5 cm (12 inch) length – stainless steel with quartz objective.

BWT-840000348

Polystyrene Validation cap with integrated ASTM standard polystyrene.

BWT-840000349

NanoRam (model BWS456-785 only) replacement shaft with objective for sampling adapters – point-and-shoot; vial holder; bottle adapter. Working distance 6 mm.

BWT-840000350

NanoRam Shaft with lens for thick container sampling. Working distance 10 mm.

BWT-840000352

LAN cable for connection to PC.

BWT-840000353

Handheld Raman shaft protective cap, package of 10.

BWT-840000354

Pouch for handheld Raman adapters compatible with NanoRam-1064, TacticID-N Plus, and TacticID Mobile.NR2-PCH-ADPT

BWT-840000355

Leather shoulder bag for NanoRam unit including one NR2-PCH-ADPT pouch for holding accessories.

BWT-840000361

Laser Power Meter, Pen Type, Calibrated. Range: 5 micro-Watts to 1 Watt. Used in OQ/PQ and annual certification laser power measurement.

BWT-840000403

Rechargeable lithium-ion battery: fits TacticID-N Plus, TacticID Mobile, and NanoRam-1064.TID-BAT

BWT-840000406

TacticID Vial-Holder Adapter, compatible with 15 mm-diameter vials.

BWT-840000414

Power adapter for 18 V DC, 1.67 A. Plugs for USA, EU, UK and AU included in the scope of delivery.TID-PWA

BWT-840000416

TacticID Point-and-Shoot adapter.

BWT-840000417

TacticID Validation Cap with integrated ASTM-standard polystyrene. For use with TacticID-N Plus and TacticID-GP Plus.

BWT-840000418

TacticID-GP and TacticID-GP Plus shaft protection cap (Yellow).TID-CAP-GP

BWT-840000419

Stylus/pen combo for touch screens (package of 5).TID-STY

BWT-840000422

TacticID hard plastic rugged carrying case.

BWT-840000428

Wireless, battery-powered portable router; 3G/4G connectivity.

BWT-840000429

TacticID-N and TacticID-N Plus shaft protection cap (Black).TID-CAP-N

BWT-840000433

NanoRam O-ring replacement kit – includes: O-rings, ID 9.00 mm, x15; O-Rings, ID 10.00 mm x15; O-rings, ID 13.00 mm x10 for the shaft in handheld Raman instruments.

BWT-840000463

BAC151x Probe Adaptor to connect B&W Tek Lab grade Raman probes to BAC151x Video microscope sampling system. Remove the standard shaft and distance regulator, to use the adaptor and connect the probe head to the video microscope. 3 adaptors per pack.

BWT-840000481

Disposable, protective sleeve for the NanoRam Immersion Probe model NR2-IMP, package of 49.

BWT-840000482

Disposable, protective sleeve for the NanoRam Immersion Probe model NR2-IMP, package of 490.

BWT-840000491

TacticID Right-Angle Adapter.

BWT-840000498

TacticID battery cartridge for use with six type 123A disposable batteries (e.g. Surefire). Batteries not included.

BWT-840000524

SERS analysis adapter for use with TacPac™-P SERS substrates.

BWT-840000528

TAP-KIT-T is a SERS Analysis kit for use with the TacticID-N Plus for Raman signal amplification and fluorescence reduction of hard-to-measure samples. This kit includes a black pouch, Tweezer, SERS Analysis Adaptor, and 25 SERS substratesSERS analysis kit for use with Raman handheld spectrometers from B&W Tek. For Raman signal amplification and fluorescence reduction of hard-to-measure samples. For use with 785 nm laser excitation. Includes: tweezers, TacPac adapter, 25 SERS strips.TAP-KIT-T

BWT-840000603

TacticID (785 nm) Pouch for Adapters

BWT-840000629

Lithium-ion battery charging cradle.

BWT-840000655

Sterilized disposable, protective sleeve for the NanoRam Immersion Probe model NR2-IMP; package of 490.

BWT-840000669

Car charger for TacticID-N Plus.

BWT-840000679

Zoom lens for our BAC100/BAC102 fiber-optic Raman probes. Working distance is adjustable from 20 mm to 60 mm. Suitable for a Raman excitation range from 500 nm to 850 nm.

BWT-840000680

Long-working-distance zoom lens for BAC100/BAC102 fiber-optic Raman probes. Working distance is adjustable from 60 mm to 600 mm. Suitable for a Raman excitation range from 500 nm to 850 nm.

BWT-840000681

A telescope Stand-off lens for BAC100/BAC102 fiber-optic Raman probes. Wide zoom range for sample measurement ranges from 0.6 meters to 6 meters. Suitable for a Raman excitation range from 500 nm to 850 nm.RTS202-VIS-NIR

BWT-840000711

Zoom lens for our BAC100/BAC102 fiber-optic Raman probes. Working distance is adjustable from 20 mm to 60 mm. Suitable for a Raman excitation range from 785 nm to 1064 nm.

BWT-840000712

Long-working-distance zoom lens for BAC100/BAC102 fiber-optic Raman probes. Working distance is adjustable from 60 mm to 600 mm. Suitable for a Raman excitation range from 1000 nm to 1100 nm.

BWT-840000858

USB cable supporting micro USB port up to type A USB 2.0.

BWT-840000881

NanoRam accessories: 0.5” outer diameter x 150 mm L (5.9”) – Raman contact probe accessory for NanoRam. Rugged 316 stainless steel shaft.

BWT-840000912

Handheld Raman O-ring replacement kit –(for shaft only).Kit includes: O-Ring#1 ID 9.00 mm x15 and O-Ring#2 ID 10.00 mm x15 (TacticID-N Plus, TacticID Mobile, and NanoRam-1064).TID-ORK

BWT-840000934

Polystyrene reference for the QT-Sampler transmission Raman accessory.

BWT-840000940

Set of 2 mm excitation aperture, collection aperture, large round sample holder and large square sample holder for QT-Sampler.

BWT-840000941

Set of 4 mm excitation aperture, collection aperture, large round sample holder and large square sample holder for QT-Sampler.

BWT-840000942

Set of 6 mm excitation aperture, collection aperture, large round sample holder and large square sample holder for QT-Sampler.

BWT-840000943

Set of 8 mm excitation aperture, collection aperture, large round sample holder and large square sample holder for QT-Sampler.

BWT-840000948

USB OTG host cable for data transmission between a USB flash drive and a handheld system.

BWT-840000949

The large-spot sampling adapter is designed for use with Metrohm handheld Raman systems, providing a larger spot size and increased sampling depth to minimize the risk of sample burning, particularly for sensitive or dark-colored samples. Additionally, this adapter supports see-through capabilities when used with devices compatible with see-through software.TID-STA

BWT-840000964

Video microscope sampling system head for use with B&W Tek's lab and industrial Raman probes. With coaxial LED illuminator for target alignment and video camera for sample observation. Compatible with standard microscope objectives. Probe not included, available separately. Objective lens not included, available separately. 785 nm configuration.

BWT-840000965

Video microscope sampling system head for use with B&W Tek's lab and industrial Raman probes. With coaxial LED illuminator for target alignment and video camera for sample observation. Compatible with standard microscope objectives. Probe not included, available separately. Objective lens not included, available separately. 532 nm configuration.

BWT-840000966

Video microscope sampling system head for use with B&W Tek's lab and industrial Raman probes. With coaxial LED illuminator for target alignment and video camera for sample observation. Compatible with standard microscope objectives. Probe not included, available separately. Objective lens not included, available separately. Dual 532/785 nm configuration.

BWT-840000969

Handheld Raman Spectrometer 1064 accessory:. Contact immersion probe, 6” length, working distance approx. 1 mm, operating pressure up to 2 bar at room temperature.NRX-CTP-IMP

BWT-840000970

Handheld Raman Spectrometer 1064 accessories: Large bottle adapter with 10 mm working distance.NRX-BSA

BWT-840000980

TacticID Plus Product Manual Set including Quick Reference Guide and TID Installation Instructions.

BWT-840000984

Video microscope sampling system head for use with B&W Tek's lab and industrial Raman probes. With coaxial LED illuminator for target alignment and video camera for sample observation. Compatible with standard microscope objectives. Probe not included, available separately. Objective lens not included, available separately. 1064 nm configuration.

BWT-840001119

Focus adapter for 785 nm See-Through Raman probes

BWT-840001120

Light shield accessory for See-Through Raman probes.

BWT-840001121

Focus adapter for 1064 nm See-Through Raman probes.

BWT-840001122

Surface regulator for See-Through Raman probe.

BWT-840001123

Bluetooth 1D barcode scanner for use with BWID software operating a portable Raman instrument

BWT-840001124

SERS analysis sample preparation kit for use with Raman handheld spectrometers from B&W Tek. For Raman signal amplification and fluorescence reduction of hard-to-measure samples. For use with 785 nm laser excitation. Disposable plastic single-use laboratory spatula, pipettes and PP graduated microcentrifuge tubes (2 ml) used to prepare samples for testing with TacPac™ SERS. Package of 25 SERS substrates included.TAP-SAM25

BWT-840001125

SERS analysis sample preparation kit for use with Raman handheld spectrometers from B&W Tek. For Raman signal amplification and fluorescence reduction of hard-to-measure samples. For use with 785 nm laser excitation. Disposable plastic single-use laboratory spatula, pipettes and PP graduated microcentrifuge tubes (2 ml) used to prepare samples for testing with TacPac™ SERS. Package of 50 SERS substrates included.TAP-SAM50

BWT-840001153

Lightweight black polycarbonate carrying case for QT-Sampler module. Watertight, crushproof, and dustproof with cube foam fitting.CCRM QT-Sampler

BWT-840001154

Shoulder bag for TacticID series. Constructed with 1000d heavy duty fabric, multiple tactical pouches and compartment designed for rugged use and hard wearing.. Compatible with all TacticID products and NanoRam products. For transportation purposes only.TID-SBG

BWT-840001177

Aperture removal tool for easy interchanging different apertures for optimal Raman spot size for transmission Raman with QT-Sampler.TOOL-APERTURE

BWT-840001178

Carrying Case for i-Raman, i-Raman Plus, i-Raman EX and GemRam systems. This is black soft carrying case with extendable handle, wheels and custom cut foam (27 to 28” case length) for safe, convenient instrument transport. (Model CCRM-GEMRAM)

BWT-840001191

Type-C to Type-A USB cable. Compatible with TacticID Mobile.HHX-USB

BWT-840001192

Power adaptor 15V 3.6A DC. Plugs for US, EU, UK and AU included. Compatible with TacticID Mobile.HHX-PWA

BWT-840001193

USB drive containing TacticID Mobile User Manual; Includes both USB type-A connector and USB type-C connector, and can be used for OTG functions.HHX-USB-OTG

BWT-840001194

Power bank (battery pack) for TacticID Mobile. Compatible with the TacticID Mobile unit and the TacticID Mobile power adaptor for charging purposes.HHX-PWB

BWT-840001202

RIS100-HS-785-08: Hastelloy immersion shaft for BAC102/BAC100B Raman probes with excitation wavelength 785nm. Features a 0.5" (12.7 mm) O.D. x 8" (203.2 mm) L Hastelloy C-276 shaft and a gold- sealed sapphire ball lens. Working distance 0.4 mm in air, 0.6 mm in water. Shaft operating temperature is up to 250 degrees C, pressure up to 4000 psi. Shaft must be purchased with B&W Tek Raman probe.RIS100-HS-785-08

BWT-840001204

RIS100-HS-532-08: Hastelloy immersion shaft for BAC102/BAC100B Raman probes with excitation wavelength 532 nm. Features a 0.5" (12.7 mm) O.D. x 8" (203.2 mm) L Hastelloy C-276 shaft and a gold- sealed sapphire ball lens. Working distance 0.4 mm in air, 0.6 mm in water. Shaft operating temperature is up to 250 degrees C, pressure up to 4000 psi. Shaft must be purchased with B&W Tek Raman probe.RIS100-HS-532-08

BWT-840001223

USB-C Car Charger for TacticID Mobile. Includes a dedicated USB-C Cable for fast charging inside a vehicle. Model HHX-CCA

BWT-840001283

The QT-Sampler is an accessory for transmission Raman measurements, enabling content uniformity testing of pharmaceutical tablets. Compatible with i-Raman NxG 785H.Apertures and sample holders are sold separately.

CABLE.BNC.50

50 cm BNC cable for diagnostics purposes.

CABLE.MONITOR

Monitor cable for modular Autolab systems, providing connections for external equipments (Potential output (Eout), Current output (iout) and Potential input (Ein)).

CABLE.MONITOR4

Monitor cable for PGSTAT101, providing connections for analog outputs (Eout, iout and Vout) and input (Vin)

CABLE.PWR

Standard power cable for Autolab instruments and accessories.

Cat-empty

CBL.BSTR20A.DIO

Digital control cable for the Autolab Booster20A.

CBL.BSTR.DIO

Digital control cable for the Autolab Booster10A.

CBL.MONIT.MAC.204.S

Monitor cable for M101/M204/PGSTAT204, providing connections for analog outputs (Eout, iout and Vout) and input (Vin).

CBL.MONITOR7.S

Monitor cable for 7 series (serial number starting with AUT7xxxx) modular Autolab systems, providing connections for external equipment (Potential output (Eout), Current output (iout) and Potential input (Ein)).

CBL.MONITOR8.S

Monitor cable for 8 series (serial number starting with AUT8xxxx) modular Autolab N systems, providing connections for external equipment (Potential output (Eout), Current output (iout) and Potential input (Ein)).

CBL.MONITOR.PG101.S

Monitor cable for PGSTAT101, providing connections for analog outputs (Eout, iout and Vout) and input (Vin).

CBL.PWR.XXX

Standard power cord to plug the VIONIC instument into the power grid. The type of the inclued power cord is region specific.

CBL.USB

Standard USB cable for Autolab instruments.

CELLCBL.101

Standard cell cable, 1.5 m, with connection for counter electrode (CE), reference electrode (RE), sense electrode (S), working electrode (WE) and ground for PGSTAT101.

CELLCBL.30.RE.S

Standard cell cable, 1.5 m, with connection for reference electrode (RE) and sense electrode (S).

CELLCBL.30.WE.S

Standard cell cable, 1.5 m, with connection for counter electrode (CE), working electrode (WE) and ground.

CELLCBL.M101.204

Standard cell cable, 1.5 m, with connection for counter electrode (CE), reference electrode (RE), sense electrode (S), working electrode (WE) and ground for M101/M204/PGSTAT204.

CORR.1LCELL.S

The Autolab 1 L corrosion cell is suitable for corrosion measurements according to ASTM standards. The cell has a thermostatic jacket for temperature control and a series of openings for counter electrodes, pH sensor, thermometer, Luggin-Haber capillary and gas purging.The 1 ll corrosion cell has been designed to measure the corrosion properties samples with a diameter ranging from 14.7 mm to 16 mm and a thickness from 0.5 mm up to 4 mm. The exposed surface is 1 cm² and the seals are made out of natural rubber.

CORR.1LHLD

CORR.1LSTL

CORR250.CELL.S

Complete cell for corrosion measurements, 250 mL.

CORR.CELL.S

The Autolab 400 ml corrosion cell is suitable for corrosion measurements. The cell has a thermostatic jacket for temperature control and a series of openings for counter electrodes, pH sensor, thermometer, Luggin-Haber capillary and gas purging.The 400 ml corrosion cell has been designed to measure the corrosion properties of 14 mm diameter and 1 mm thick flat circular samples immersed in an electrolyte. The exposed surface area is 0.785 cm². The holder is made of Delrin with a Viton seal.

CORR.THERM

Glass thermometer (-20 °C to 150 °C).

CUV-UV/VIS

The cuvette holder provides the possibility to carry out transmission measurements using a classic 10 mm glass or quartz cuvette. The holder is fitted with two SMA-905 connectors with collimating lenses built-in. A cover is provided to shield the cuvette from environmental light.

DIO12.SPEC.TRIGGER.S

Triggering cable required for synchronized spectroelectrochemical measurement in combination with Autolab instruments equipped with a DIO12 interface. This cable provides a direct connection between the digital input/output (DIO) port of the Autolab and the Autolab light source and Autolab spectrophotometer. The connection to the light source enables the remote control of the shutter and the connection to the spectrophotometer provides the possibility to synchronize the acquisition of spectroscopy data with the acquisition of electrochemical data.

DIO48.SPEC.TRIGGER.S

Triggering cable required for synchronized spectroelectrochemical measurement in combination with Autolab instruments equipped with a DIO48 interface. This cable provides a direct connection between the digital input/output (DIO) port of the Autolab and the Autolab light source and Autolab spectrophotometer. The connection to the light source enables the remote control of the shutter and the connection to the spectrophotometer provides the possibility to synchronize the acquisition of spectroscopy data with the acquisition of electrochemical data.

DRP-4MMHCAST8

Eight channel boxed connector suitable to improve the set-up confirguration acting as an interface between uStat-i MultiX and screen-printed electrodes.

DRP-ALCRUCIBPACK

Aluminum crucibles (5 x 1.6 mm ; 5 x 4.2 mm) to be used in combination with RAMANCELL to perform Raman measurements over solid samples.

DRP-BANANA4TO2MM

Adaptor from 4 mm male banana connections to 2 mm female connections

DRP-BIASTIR

Stirrer for batch injection analysis cells. The stirring rod in Teflon allows a precise control of the rotation rate

DRP-BICASTDIR

Connector that acts as an interface between our dual screen-printed electrodes and Metrohm DropSens instruments and some accessories.

DRP-BIDSC4MM

Connector that functions as an interface between DropSens dual screen-printed electrodes (SPEs) and interdigitated electrodes with any type of potentiostat.

DRP-BIDSC-FET

Boxed connector that acts as an interface between ref. AUFET30 electrodes and any kind of potentiostat

DRP-BINP-PUR

DRP-CABSTAT

Flexible cable connector that acts as an interface between DropSens bipotentiostats and conventional electrodes

DRP-CAC4MMH

Flexible cable that act as an interface between ceramic substrate SPEs and any kind of potentiostat

DRP-CACIDEMEA

Flexible cable that act as an interface between interdigitated electrodes in glass with CE and RE and any kind of potentiostat.Cable connector for interdigitated electrodes with CE and RE quantity

DRP-CAC-NTC

Flexible cable that act as an interface between ref.C110-NTC SPEs and any kind of potentiostat

DRP-CASTDIR

Connects single (1 WE) SPEs to μStat 200, μStat 300, μStat 400, μStat 4000/P, μStat 8000/P, μStatECL, SpectroECL and the SPELEC line of instruments.

DRP-CAST-P

Flexible cable that act as an interface between plastic substrate SPEs and DropSens potentiostats

DRP-CAST-TLFCL

Cable connector from μStat instruments and the SPELEC line of instruments to TLFCL format SPEs

DRP-CDIOCABLE400

DRP-CDIOCABLEMULTI

DRP-CELL-IDE

Cells for batch analysis with interdigitated electrodes (IDE). Suitable for working with volumes up to 3-8 ml and manufactured in different materials that will allow you to work even with organic solvents.

DRP-CELL-IDE-PEEK

DRP-CFLWCL-CONICPEEK

DRP-CFLWCL-WE-PEEK

DRP-CONNECTOR96X-SYN

DRP-CUNP-PUR

DRP-DIOC200SYNC96

Cable connector suitable to connect SYNCONN96X with STAT200 for automation of the electrochemical ELISA System

DRP-DIOC400SYNC96

Cable connector suitable to connect SYNCONN96X with STAT300 and STAT400 for automation of the electrochemical ELISA System

DRP-DIOC8000SYNC96

Cable connector suitable to connect SYNCONN96X with STAT4000/P and 8000/P for automation of the electrochemical ELISA System

DRP-DIOMULTISYNC96

DRP-DSC4MM

Connector that functions as an interface between DropSens screen-printed electrodes (SPEs) and interdigitated electrodes with any type of potentiostat.

DRP-DTIPD1000

Pipette tip boxes to be used with P1000M micropipette included in BIASPE10 cell

DRP-DTIPD200

Pipette tip boxes to be used with P200M micropipette included in BIASPE02 cell

DRP-ECLPHOTODIODCELL

Cell for screen-printed electrodes to perform electrochemiluminescence measurements. This ABS cell includes a Silicon photodiode with preamp with a spectral response range 340 - 1100 nm and peak sensitivity wavelength of 960nm. This cell should be used in combination with µStat ECL or µStat SpectroECL electrochemiluminiscence instruments.

DRP-FLKIT

Kit for performing fluorescence experiments composed by 2 x short optical fibers (600 µm) ended in SMA 905 connections, 2 x optical filters one of 230-500 nm and other for 300-750 nm wavelength and 2 x holders for the filters.Complete your set up by adding the required excitation light depending on the range of interest (ref. LEDUV275, LEDVIS395 or LEDRGB).For performing fluorescence spectroscopy experiments coupled to spectroelectrochemistry (ref. SPELEC) with SPEs acquire the suitable reflection probe (RPROBE) and reflection cell (REFLECELL).

DRP-FLKITSPE

Kit designed for those researchers interested in performing fluorescence spectroscopy experiments with screen-printed electrodes (Includes 2 x optical fibers (600 um) ended in SMA 905 connections, 2 x optical filters 230-500 and 300-750 nm 2 x holders, 1 x RPROBE-VIS-UV and 1 x REFLECELL).

DRP-FLWCL-IDE-PEEK

DRP-FOLSOL-AQU-1ML

DRP-FOLSOL-AQU-5ML

DRP-GQD

DRP-HCELL

This cell consists of two electrochemical compartments in which hydrogen is produced in the load cell and detected in the oxidation cell. It can be used to evaluate hydrogen uptake, permeability and transport in a variety of metal membranes, among other applications.

DRP-HCELLKIT

DRP-I-BICAST

Connector that acts as an interface between our dual screen-printed electrodes and Metrohm DropSens potentiostats.

DRP-I-CABSTAT

μStat Cable connector for μStat-i 400 and conventional electrodes

DRP-I-CABSTAT1

μStat Cable connector for μStat-i 400s and conventional electrodes

DRP-I-CAST

Connector that act as an interface between our Screen-Printed Electrodes and Metrohm DropSens potentiostats.

DRP-IRNP-COL

DRP-I-VKIT

Kit for verifying the correct performance of instruments: μStat-i 400s, μStat-i 400s and μStat-i MultiX

DRP-LEDRGB

LED light for performing fluorescence spectroscopy experiments coupled to spectroelectrochemistry

DRP-LEDUV275

LED light for performing fluorescence spectroscopy experiments coupled to spectroelectrochemistry

DRP-LEDVIS395

LED light of 395 nm wavelength

DRP-PTAUNINW-LO-1.5

DRP-PTAUNINW-SH-1.5

DRP-PTGRID-TRANSCELL

This cell allows mass electrolysis to be easily performed while transmission measurements (1 mm optical path) are acquired in the solution close to the electrode.

DRP-RAMANCELL-C

Cell in PEEK for Raman spectroelectrochemical measurements. Designed be used with ref. RAMANPROBE and conventional Metrohm electrodes.

DRP-RAMANCELL-M

Cell for spectroelectrochemical applications in combination with a microscope, allowing the laser focus onto the surface of the working electrode, obtaining valuable information while the electrochemical process takes place.

DRP-RAMANCELLS-U3